Le CSTAR CSQD-45 4.5 Ton Diesel Forklift Truck est évalué pour 4,500 kg at a 500 mm load center. It uses a Xinchai A498BPG diesel engine, a seated driving position and pneumatic tires. The specified mast provides a maximum no-load lifting height of 3 000 mm.
The CSQD-45 measures 1,400 mm wide and has a minimum outer turning radius of 2,820 mm. Its lowered mast stands 2,370 mm high, while the overhead guard measures 2 230 mm.
CSQD-45 Technical Specifications
| Paramètre Technique | Unité | CSQD-45 |
|---|---|---|
| Modèle | — | CSQD-45 |
| Puissance | — | Diesel |
| Charge de levage nominale | kg | 4500 |
| Distance du centre de charge | mm | 500 |
| Mode de conduite | — | Conduite de siège |
| Length (With fork) | mm | 4120 |
| Length (Without fork) | mm | 3050 |
| Largeur | mm | 1400 |
| Height when the mast not raised | mm | 2370 |
| Overhead guard height | mm | 2230 |
| Empattement | mm | 1900 |
| Surplomb avant | mm | 590 |
| Surplomb arrière | mm | 550 |
| Dégagement au sol minimum | mm | 150 |
| Hauteur de levage maximale à vide | mm | 3000 |
| Hauteur de levage libre | mm | 150 |
| Rayon de braquage minimal (côté extérieur) | mm | 2820 |
| Angle d'inclinaison du mât (avant/arrière) | ° | 6 / 12 |
| Vitesse de levage maximale à vide | mm/s | 460 |
| Vitesse de levage maximale à pleine charge | mm/s | 420 |
| Vitesse de travail maximale à vide | km/h | 24 |
| Vitesse de travail maximale à pleine charge | km/h | 24 |
| Qualification maximale à pleine charge | % | 20 |
| Poids du chariot élévateur dans des conditions standard à vide | kg | 5860 |
| Axle full load F/R | kg | 9080 / 1370 |
| Axle no load F/R | kg | 2950 / 3780 |
| Tire no. (F/R) | — | 2 / 2 |
| Type de pneu (F/R) | — | Pneumatic tire |
| Frein/frein de service | — | Pédale-frein électrique |
| Frein de stationnement | — | Mécanique-manuel |
| Tension/capacité de la batterie | V/Ah | 2-12/80A |
| Modèle moteur | — | Xinchai A498BPG, China II |
| Capacité du réservoir de carburant du moteur | L | 65 |
4.5 Ton Capacity at a 500 mm Load Center
The CSQD-45 combines a 4,500 kg rated capacity avec un centre de charge de 500 mm. These two figures belong together: load dimensions and the position of the center of gravity matter alongside total weight.
If you handle long machinery, irregular loads or use attachments, include those details in your quotation request. Load weight, dimensions and placement height give the CSTAR team a clear starting point for reviewing the truck configuration.
A 1,400 mm Wide 4.5 Ton Diesel Forklift
The CSQD-45 is 1,400 mm wide et 3,050 mm long without forks. Overall length with forks is 4,120 mm, with a wheelbase of 1 900 mm.
These dimensions help you compare the truck with existing entrances, loading areas and travel routes. Include the size of your largest load when measuring the space needed along those routes.
Turning Radius and Working Space
The CSQD-45 has a 2,820 mm minimum outer turning radius. For straight travel, overall width is a useful starting point. Turning into a rack introduces another factor: the space occupied by the truck and its load throughout the turn.
Right-angle stacking space depends on pallet dimensions, fork-entry direction and nearby obstructions as well as the truck’s turning radius. Providing those measurements makes the layout review more useful than comparing aisle width with turning radius alone.
Mast Height and Doorway Clearance
The specified mast provides a 3,000 mm maximum no-load lifting height et 150 mm free lift. Mast tilt is 6° forward and 12° backward.
With the mast lowered, its height is 2,370 mm; the overhead guard measures 2 230 mm. The mast is therefore the taller of these two components. Use that dimension when starting your doorway-clearance check, and allow for the clearance required by your site.
Xinchai Engine and Pneumatic Tires
The CSQD-45 uses a Xinchai A498BPG diesel engine. The supplied engine configuration is specified as China II, and fuel tank capacity is 65 L.
The truck is fitted with two front pneumatic tires and two rear pneumatic tires, with a minimum ground clearance of 150 mm. Include your destination country in the inquiry so the engine configuration can be reviewed against the requirements of your market.
Loaded and Unloaded Performance
Maximum lifting speed is 460 mm/s without load et 420 mm/s under full load. Maximum travel speed is 24 km/h in both conditions.
Full-load maximum gradeability is 20%. The separate loaded and unloaded figures make it easier to compare performance specifications under matching conditions.
Machine Weight and Axle-Load Data
Forklift weight under the standard no-load condition is 5,860 kg. The technical table also lists front and rear axle loads separately for loaded and unloaded conditions.
If axle-load data will be used for floor, dock, ramp or transport calculations, confirm the applicable figures for the final machine configuration before using them for engineering decisions.
CSQD-45 Ordering Questions
What load information should I provide for a CSQD-45 quotation?
Provide the maximum load weight, load dimensions, fork-entry direction and required lifting or placement height. Include any attachments you plan to use.
Which engine powers the CSQD-45?
The CSQD-45 uses a Xinchai A498BPG diesel engine. The supplied configuration is specified as China II and has a 65 L fuel tank.
Which height should I check for doorway access?
The lowered mast measures 2,370 mm and the overhead guard measures 2,230 mm. The mast is the taller of these two components, so start with the 2,370 mm dimension when reviewing doorway access.
Can the 2,820 mm turning radius be used as the required aisle width?
Turning radius and stacking aisle width describe different measurements. Right-angle handling space also depends on pallet dimensions, fork-entry direction and the space occupied by the truck and load during the maneuver.
Send your load weight and dimensions, required lift height, working-area measurements, attachment requirements, destination country and order quantity to CSTAR Machinery.
